HYPERX

Sort By:  
HyperX Fury Black 4GB, DDR3, 1600MHz (PC3-12800), CL10, DIMM Memory
HyperX Fury Black 4GB, DDR3, 1600MHz (PC3-12800), CL10, DIMM Memory (D3-4G1600KHX10-FUBLK)
HX316C10FB/4 
4GB 512M x 64-Bit DDR3-1600 CL10 240-Pin DIMM
 
HyperX HX316C10FB/4 is a 512M x 64-bit (4GB) DDR3-1600 CL10 SDRAM (Synchronous DRAM) 1Rx8 memory module, based on eight 512M x 8-bit DDR3 FBGA components. This module has been tested to run at DDR3-1600 at a low latency timing of 10-10-10 at 1.5V. Additional timing parameters are shown in the PnP Timing Parameters section below. 
 
 
 
Features
 
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), single sided component
£31.20
HyperX Fury Black 4GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory
HyperX Fury Black 4GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory (D4-4G2400KHX15-FU)

HyperX HX424C15FB/4 is a 512M x 64-bit (4GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V. 

 

  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.2V to 3.6V
  • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
  • Low-power auto self refresh (LPASR)
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration
  • Single-rank
  • On-board I2 serial presence-detect (SPD) EEPROM
  • 16 internal banks; 4 groups of 4 banks each
  • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
  • Height 1.340” (34.04mm), w/heatsink
£32.80
HyperX Fury Black 4GB, DDR4, 2666MHz (PC4-21330), CL15, DIMM Memory
HyperX Fury Black 4GB, DDR4, 2666MHz (PC4-21330), CL15, DIMM Memory (D4-4G2666KHX15-FU)
 
HyperX HX426C15FB/4 is a 512M x 64-bit (4GB) DDR4-2666 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-2666 at a low latency timing of 15-17-17 at 1.2V.
 
 
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.2V to 3.6V
  • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
  • Low-power auto self refresh (LPASR)
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration
  • Single-rank
  • On-board I2 serial presence-detect (SPD) EEPROM
  • 16 internal banks; 4 groups of 4 banks each
  • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
  • Height 1.340” (34.04mm), w/heatsink 
£34.14
HyperX Fury Black 8GB, DDR3, 1600MHz (PC3-12800), CL10, DIMM Memory
HyperX Fury Black 8GB, DDR3, 1600MHz (PC3-12800), CL10, DIMM Memory (D3-8G1600KHX10-FUBLK)


8GB 1G x 64-Bit DDR3-1600 CL10 240-Pin DIMM

HyperX HX316C10FB/8 is a 1G x 64-bit (8GB) DDR3-1600 CL10 SDRAM (Synchronous DRAM) 2Rx8 memory module, based on sixteen 512M x 8-bit DDR3 FBGA components. This module has been tested to run at DDR3-1600 at a low latency timing of 10-10-10 at 1.5V.
 
 
 
Features
 
•JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), double sided component
£52.11
HyperX Fury Black 8GB, DDR4, 2666MHz (PC4-21330), CL16, XMP, DIMM Memory
HyperX Fury Black 8GB, DDR4, 2666MHz (PC4-21330), CL16, XMP, DIMM Memory (D4-8G2666KHX16-FUBLKV2)
 
HyperX HX424C12SB2K2/16 is a kit of two 1G x 64-bit (8GB) DDR4-2400 CL12 SDRAM (Synchronous DRAM) 2Rx8, memory modules, based on sixteen 512M x 8-bit FBGA components per module. Total kit capacity is 16GB. Each module supports Intel® XMP (Extreme Memory Profiles). Each module has been tested to run at DDR4-2400 at a low latency timing of 12-14-14 at 1.35V. The SPDs are programmed to JEDEC standard latency DDR4-2133 timing of 15-15-15 at 1.2V. Each 288-pin DIMM uses gold contact fingers. 
 
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.25V to 3.6V
  • On-Die termination (ODT)
  • 16 internal banks; 4 groups of 4 banks each
  • Bi-Directional Differential Data Strobe
  • 8 bit pre-fetch
  • Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)
  • Height 1.36” (34.57mm)

 

£61.50
HyperX Fury Black 8GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory, Single Rank
HyperX Fury Black 8GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory, Single Rank (D4-8G2400KHX15-FUBLK-V2)

HyperX HX424C15FB2/8 is a 1G x 64-bit (8GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. 
 
 
Features
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.2V to 3.6V
  • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
  • Low-power auto self refresh (LPASR)
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration
  • Single-rank
  • On-board I2 serial presence-detect (SPD) EEPROM
  • 16 internal banks; 4 groups of 4 banks each
  • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
£62.06
HyperX Fury Black 16GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory
HyperX Fury Black 16GB, DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory (D4-16G2400KHX15-FUBLK)
 
HyperX HX424C15FB/16 is a 2G x 64-bit (16GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 1G x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V. 
 
 
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.2V to 3.6V
  • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
  • Low-power auto self refresh (LPASR)
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration
  • Dual-rank
  • On-board I2 serial presence-detect (SPD) EEPROM
  • 16 internal banks; 4 groups of 4 banks each
  • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
  • Height 1.340” (34.04mm), w/o heatsink
£129.54
HyperX Fury Black 32GB Kit (4 x 8GB), DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory
HyperX Fury Black 32GB Kit (4 x 8GB), DDR4, 2400MHz (PC4-19200), CL15, 1.2V, XMP 2.0, DIMM Memory (D4-32G2400KHX15K4-FUBLKV2)
 
32GB (8GB 1G x 64-Bit x 4 pcs.) DDR4-2400 CL15 288-Pin DIMM
 
HyperX HX424C15FBK4/32 is a kit of four 1G x 64-bit (8GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 512M x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Total kit capacity is 32GB. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V.
 
 
 
 
Features
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.2V to 3.6V
  • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
  • Low-power auto self refresh (LPASR)
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration
  • Dual-rank
  • On-board I2 serial presence-detect (SPD) EEPROM
  • 16 internal banks; 4 groups of 4 banks each
  • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
  • Height 1.340” (34.04mm), w/o heatsink
£266.36
HyperX Fury Black 32GB Kit (4 x 8GB), DDR4, 2666MHz (PC4-21330), CL16, 1.2V, XMP 2.0, DIMM Memory
HyperX Fury Black 32GB Kit (4 x 8GB), DDR4, 2666MHz (PC4-21330), CL16, 1.2V, XMP 2.0, DIMM Memory (D4-32G2666KHX16K4-FUBLKV2)

32GB (8GB 1G x 64-Bit x 4 pcs.) DDR4-2666 CL16 288-Pin DIMM
 
HyperX HX426C16FB2K4/32 is a kit of four 1G x 64-bit (8GB) DDR4-2666 CL16 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module kit supports Intel® Extreme Memory Profiles (Intel® XMP) 2.0. Total kit capacity is 32GB. Each module has been tested to run at DDR4-2666 at a low latency timing of 16-18-18 at 1.2V. 
 
 
 
 
Features
  • Power Supply: VDD = 1.2V Typical
  • VDDQ = 1.2V Typical
  • VPP - 2.5V Typical
  • VDDSPD = 2.25V to 3.6V
  • On-Die termination (ODT)
  • 16 internal banks; 4 groups of 4 banks each
  • Bi-Directional Differential Data Strobe
  • 8 bit pre-fetch
  • Burst Length (BL) switch on-the-fly BL8 or BC4(Burst Chop)
  • Height 1.340” (34.04mm), w/heatsink
 
£280.93
Per Page      1 - 9 of 9
  • 1
Back to top